LEGO® 21343 CONVERSION BETA
Viking Village
An independently prepared component plan based on the original Light My Bricks 1.0 inventory.
21343-beta.2 · Source checked 2026-10-29 · Physical installation untested
READ BEFORE ORDERING
THIS BUILD.
THE IMPORTANT DETAILS.
- 4 Dock housings need new Tether attachment locations. Check the stud footprint, housing clearance and access to both Belt sockets at each original board location before buying.
- This kit uses 1 FX Spectrum controller(s). Select the matching mode and connect only the intended fixtures to effect outputs. The original effect timing is not reproduced exactly. Mounting needs 3×3 studs and 17 mm clearance; preserve access to the dial.
- Capacity allowance: 14 Astro light/string connectors across 24 Dock Astro ports. This checks total capacity only. Assign lights by their actual locations and confirm each Dock’s local capacity and lead reach before buying.
- This is an independently derived component plan, not a physically tested installation or a replacement step-by-step instruction manual. Use the original guide together with the concordance and changed mounting/power plan.
Connection counts are a planning check. They do not verify local grouping, cable reach, power draw or physical fit. Astro ports and Belt sockets are different connections.
How the cable allowance was calculated
6 network components require at least 5 Belt links in this planning allowance. Original cable lengths are retained where mapped; included FX Belts are credited once. Extra links use 50 cm Belts as an unmeasured routing allowance. Check the actual branch and effect grouping against every source step.
THE CONCORDANCE
EVERY CHANGE.
IN PLAIN SIGHT.
Quantities below are individual components. The shopping list combines shared packs, then rounds up once.
| Original 1.0 item | Proposed 2.0 replacement | What to check |
|---|---|---|
| 1 x Light Blue Large 30cm Bit Light | 1 × Astro Light Large - Light Blue 30cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 30 cm lead reaches the chosen Dock. |
| 1 x Orange Large 30cm Bit Light | 1 × Astro Light Large - Orange 30cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 30 cm lead reaches the chosen Dock. |
| 2 x Light Blue 30cm Bit Light | 2 × Astro Light Regular - Light Blue 30cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 30 cm lead reaches the chosen Dock. |
| 3 x Orange 30cm Bit Light | 3 × Astro Light Regular - Orange 30cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 30 cm lead reaches the chosen Dock. |
| 5 x White 30cm Bit Light | 5 × Astro Light Regular - White 30cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 30 cm lead reaches the chosen Dock. |
| 2 x White 30cm Micro Bit Light | 2 × Astro Light Micro - Cool White 30cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 30 cm lead reaches the chosen Dock. White is substituted with cool white; appearance may differ. |
| 1 x Flicker Effects Board | 1 × FX Spectrum ↗ | Use FX Spectrum with the closest appropriate mode: Elements for fire/flicker, Pulse, Gun, Emergency, Spooky, Sequence, Traffic or Glitter. Timing and output groups differ from 1.0. Each includes one 15 cm Belt and a 3×3 Tether. |
| 3 x 6-Port Expansion Board | 3 × Dock 6 ↗ | Astro ports are separate from the two Belt sockets. Mount the larger 2.0 housing with its included Tether; check the 1.0 board location has clearance. |
| 1 x 4-Port Micro Expansion Board | 1 × Dock 6 ↗ | Astro ports are separate from the two Belt sockets. Mount the larger 2.0 housing with its included Tether; check the 1.0 board location has clearance. |
| 10 x Adhesive Square | No separate purchase | Use the Tethers supplied with the selected Docks and Meteors. Find new stud attachment points; the old adhesive locations are not guaranteed to fit. |
| 1 x USB Power Cable | No separate purchase | Power changes to a 60 cm USB Flux Belt and separately purchased manufacturer-specified 5V/2.4A supply. Old battery/USB alternatives are not added twice. |
| 2 x 5cm Connecting Cable | 2 × Belt 5cm ↗ | Preserves the original nominal cable length. Belt plugs and routes differ; measure reach including bends before ordering. |
| 2 x 30cm Connecting Cable | 2 × Belt 30cm ↗ | Preserves the original nominal cable length. Belt plugs and routes differ; measure reach including bends before ordering. |
| 2.0 effect branch distribution | 1 × Split Dock ↗ | Each Split Dock has four Belt sockets: incoming power, effect-controller branch and onward trunk leave one spare. Keep steady lights off effect outputs. |
| 2.0 USB power entry | 1 × Flux Belt 60cm ↗ | One Flux Belt per retained power group (old AA/USB alternatives combined). USB adapter or power bank excluded. Multiple sources must feed electrically separate networks; never join powered outputs. |
BRING YOUR OWN BRICKS
THE EXTRA
LEGO PIECES.
The lighting cart excludes the LEGO set and all extra LEGO pieces. These are the pieces listed in the original guide; adapting 2.0 mounting may require additional pieces.
- 1 × Plate, Round 1x1 - Trans Dark Green
- 2 × Plate, Round 1x1 Open Stud - Trans Orange
- 4 × Plate, Round 1x1 Open Stud - Gold
- 1 × Plate, Round 1x1 Open Stud - Light Grey
- 5 × Plate, Round 1x1 Open Stud - Black
- 2 × Minifigure, Plume Feather Triple Compact / Flame / Water - Trans-Orange
- 2 × Arm Skeleton, Bent with Clips at 90 degrees (Vertical Grip) - Black
- 1 × Plate, Modified 1x1 with Open O Clip (Horizontal Grip) - Black
- 1 × Tile, Modified 1x1 with Open O Clip - Black
- 1 × Bracket 1x1 - 1x1 - Light Bluish Gray
- 1 × Plate, Round 1x1 with Bar Handle - Black
- 2 × Minifigure, Utensil Telescope - Pearl Gold
Match shape, size and colour against the original guide. Element IDs are omitted where the source does not identify them. Docks and Meteors include the Tethers stated on their product listings.
PACK-AWARE PARTS
CHECK IT.
THEN BUILD YOUR CART.
Enter individual compatible 2.0 components you already own. A pack can contain multiple lights, strings or Belts. Included FX controller Belts are deducted automatically; if you own an FX controller, enter any separate Belts you own as well.
| 2.0 product | Need | Own | Per pack | Buy packs | Spare | AUD |
|---|---|---|---|---|---|---|
| Loading the parts list… | ||||||
Prices and stock checked 29 October 2026. Shipping, taxes, discounts and live availability are determined by the retailer. A Flux Belt is a power cable, not a USB power supply.
CHECK THE SOURCE
ORIGINAL
INSTRUCTIONS.
LIGHT MY BRICKS Viking Village 21343 Instructions_Compressed ↗Original lighting inventory
- 1 x Light Blue Large 30cm Bit Light
- 1 x Orange Large 30cm Bit Light
- 2 x Light Blue 30cm Bit Light
- 3 x Orange 30cm Bit Light
- 5 x White 30cm Bit Light
- 2 x White 30cm Micro Bit Light
- 1 x Flicker Effects Board
- 3 x 6-Port Expansion Board
- 1 x 4-Port Micro Expansion Board
- 10 x Adhesive Square
- 1 x USB Power Cable
- 2 x 5cm Connecting Cable
- 2 x 30cm Connecting Cable
Original instructions and kit photography © Light My Bricks. Conversion commentary and calculations by BrickLight Chronicles. LEGO® and Light My Bricks are not endorsing this converter.