LEGO® 71006 CONVERSION BETA
Simpsons House
An independently prepared component plan based on the original Light My Bricks 1.0 inventory.
71006-beta.2 · Source checked 2026-10-26 · Physical installation untested
READ BEFORE ORDERING
THIS BUILD.
THE IMPORTANT DETAILS.
- 2 Dock housings need new Tether attachment locations. Check the stud footprint, housing clearance and access to both Belt sockets at each original board location before buying.
- The 12 original strip-light location(s) use Micro Meteors in this proposal. Find 1×3 stud attachment points with 6.4 mm height clearance. Do not assume the old adhesive position will accept a housing.
- The source inventory lists multiple supply groups. 2 Flux Belts are budgeted. Power each group separately; no USB supplies are included. Verify which components belong to each original group.
- The original includes a separate flat battery pack as well as AA power. Check each circuit before combining them into a USB layout.
- The house opens and has removable roof sections. Leave accessible disconnects and check all twelve strip-light mounting points.
- Capacity allowance: 6 Astro light/string connectors across 12 Dock Astro ports. This checks total capacity only. Assign lights by their actual locations and confirm each Dock’s local capacity and lead reach before buying.
- This is an independently derived component plan, not a physically tested installation or a replacement step-by-step instruction manual. Use the original guide together with the concordance and changed mounting/power plan.
Connection counts are a planning check. They do not verify local grouping, cable reach, power draw or physical fit. Astro ports and Belt sockets are different connections.
How the cable allowance was calculated
14 network components require at least 13 Belt links in this planning allowance. Original cable lengths are retained where mapped; included FX Belts are credited once. Extra links use 50 cm Belts as an unmeasured routing allowance. Check the actual branch and effect grouping against every source step.
THE CONCORDANCE
EVERY CHANGE.
IN PLAIN SIGHT.
Quantities below are individual components. The shopping list combines shared packs, then rounds up once.
| Original 1.0 item | Proposed 2.0 replacement | What to check |
|---|---|---|
| 12 x LED White Strip Lights | 12 × Meteor Light Micro - White ↗ | One Micro Meteor per strip location. Its 1×3 Tether mount and 23.8×8×6.4 mm housing need different attachment and clearance. Fixture count is preserved; brightness and spread may differ. |
| 2 x White 30cm Bit Lights | 2 × Astro Light Regular - White 30cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 30 cm lead reaches the chosen Dock. |
| 4 x White 15cm Bit Lights | 4 × Astro Light Regular - White 15cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 15 cm lead reaches the chosen Dock. |
| 2 x 6-Port Expansion boards | 2 × Dock 6 ↗ | Astro ports are separate from the two Belt sockets. Mount the larger 2.0 housing with its included Tether; check the 1.0 board location has clearance. |
| 1 x 30cm Connecting Cable | 1 × Belt 30cm ↗ | Preserves the original nominal cable length. Belt plugs and routes differ; measure reach including bends before ordering. |
| 6 x 15cm Connecting Cables | 6 × Belt 15cm ↗ | Preserves the original nominal cable length. Belt plugs and routes differ; measure reach including bends before ordering. |
| 5 x 5cm Connecting cables | 5 × Belt 5cm ↗ | Preserves the original nominal cable length. Belt plugs and routes differ; measure reach including bends before ordering. |
| 1 x AA Battery Pack (3x AA batteries not included) | No separate purchase | Power changes to a 60 cm USB Flux Belt and separately purchased manufacturer-specified 5V/2.4A supply. Old battery/USB alternatives are not added twice. |
| 1 x Flat Battery Pack (2x CR2032 batteries included) | No separate purchase | Power changes to a 60 cm USB Flux Belt and separately purchased manufacturer-specified 5V/2.4A supply. Old battery/USB alternatives are not added twice. |
| 3 x Adhesive squares | No separate purchase | Use the Tethers supplied with the selected Docks and Meteors. Find new stud attachment points; the old adhesive locations are not guaranteed to fit. |
| Additional 2.0 links | 1 × Belt 50cm ↗ | 14 power-network components need at least 13 links. 12 source-length Belts plus 0 Belts included with FX controllers leave 1 additional links. 50 cm is a conservative routing allowance, not a measured installation length. |
| 2.0 USB power entry | 2 × Flux Belt 60cm ↗ | One Flux Belt per retained power group (old AA/USB alternatives combined). USB adapter or power bank excluded. Multiple sources must feed electrically separate networks; never join powered outputs. |
BRING YOUR OWN BRICKS
THE EXTRA
LEGO PIECES.
The lighting cart excludes the LEGO set and all extra LEGO pieces. These are the pieces listed in the original guide; adapting 2.0 mounting may require additional pieces.
- 12 × LEGO Plates 1×6 ( for mounting strip lights)
Match shape, size and colour against the original guide. Element IDs are omitted where the source does not identify them. Docks and Meteors include the Tethers stated on their product listings.
PACK-AWARE PARTS
CHECK IT.
THEN BUILD YOUR CART.
Enter individual compatible 2.0 components you already own. A pack can contain multiple lights, strings or Belts. Included FX controller Belts are deducted automatically; if you own an FX controller, enter any separate Belts you own as well.
| 2.0 product | Need | Own | Per pack | Buy packs | Spare | AUD |
|---|---|---|---|---|---|---|
| Loading the parts list… | ||||||
Prices and stock checked 29 October 2026. Shipping, taxes, discounts and live availability are determined by the retailer. A Flux Belt is a power cable, not a USB power supply.
CHECK THE SOURCE
ORIGINAL
INSTRUCTIONS.
Light My Bricks : Simpsons House LED Lighting Kit ↗Original lighting inventory
- 12 x LED White Strip Lights
- 2 x White 30cm Bit Lights
- 4 x White 15cm Bit Lights
- 2 x 6-Port Expansion boards
- 1 x 30cm Connecting Cable
- 6 x 15cm Connecting Cables
- 5 x 5cm Connecting cables
- 1 x AA Battery Pack (3x AA batteries not included)
- 1 x Flat Battery Pack (2x CR2032 batteries included)
- 3 x Adhesive squares
Original instructions and kit photography © Light My Bricks. Conversion commentary and calculations by BrickLight Chronicles. LEGO® and Light My Bricks are not endorsing this converter.