LEGO® 71741 CONVERSION BETA
Ninjago City Gardens
An independently prepared component plan based on the original Light My Bricks 1.0 inventory.
71741-beta.2 · Source checked 2026-10-29 · Physical installation untested
READ BEFORE ORDERING
THIS BUILD.
THE IMPORTANT DETAILS.
- Source inventory marks spares for White Strip Lights but does not identify the installed count. The plan conservatively retains all 14 units; check the blueprint before reducing them.
- Source inventory marks spares for Blue 30cm Bit Lights but does not identify the installed count. The plan conservatively retains all 13 units; check the blueprint before reducing them.
- Source inventory marks spares for White 15cm Bit Lights but does not identify the installed count. The plan conservatively retains all 10 units; check the blueprint before reducing them.
- Source inventory marks spares for 8-Port Expansion Board but does not identify the installed count. The plan conservatively retains all 4 units; check the blueprint before reducing them.
- Source inventory marks spares for 5cm Connecting Cables but does not identify the installed count. The plan conservatively retains all 10 units; check the blueprint before reducing them.
- Source inventory marks spares for 15cm Connecting Cables but does not identify the installed count. The plan conservatively retains all 13 units; check the blueprint before reducing them.
- 14 Dock housings need new Tether attachment locations. Check the stud footprint, housing clearance and access to both Belt sockets at each original board location before buying.
- This kit uses 1 FX Spectrum controller(s). Select the matching mode and connect only the intended fixtures to effect outputs. The original effect timing is not reproduced exactly. Mounting needs 3×3 studs and 17 mm clearance; preserve access to the dial.
- The 14 original strip-light location(s) use Micro Meteors in this proposal. Find 1×3 stud attachment points with 6.4 mm height clearance. Do not assume the old adhesive position will accept a housing.
- At least one 12-port board is split into a Dock 9 and Dock 3. Check room for both, leave a Belt connection between them, and keep the original light groups together where possible.
- Capacity allowance: 48 Astro light/string connectors across 96 Dock Astro ports. This checks total capacity only. Assign lights by their actual locations and confirm each Dock’s local capacity and lead reach before buying.
- This is an independently derived component plan, not a physically tested installation or a replacement step-by-step instruction manual. Use the original guide together with the concordance and changed mounting/power plan.
48Astro connections
96Dock Astro ports budgeted
29Belts, including bundled
Connection counts are a planning check. They do not verify local grouping, cable reach, power draw or physical fit. Astro ports and Belt sockets are different connections.
How the cable allowance was calculated
30 network components require at least 29 Belt links in this planning allowance. Original cable lengths are retained where mapped; included FX Belts are credited once. Extra links use 50 cm Belts as an unmeasured routing allowance. Check the actual branch and effect grouping against every source step.
THE CONCORDANCE
EVERY CHANGE.
IN PLAIN SIGHT.
Quantities below are individual components. The shopping list combines shared packs, then rounds up once.
| Original 1.0 item | Proposed 2.0 replacement | What to check |
|---|---|---|
| 14 x White Strip Lights | 14 × Meteor Light Micro - White ↗ | One Micro Meteor per strip location. Its 1×3 Tether mount and 23.8×8×6.4 mm housing need different attachment and clearance. Fixture count is preserved; brightness and spread may differ. |
| 13 x Blue 30cm Bit Lights | 13 × Astro Light Regular - Blue 30cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 30 cm lead reaches the chosen Dock. |
| 10 x White 15cm Bit Lights | 10 × Astro Light Regular - White 15cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 15 cm lead reaches the chosen Dock. |
| 1 x White 30cm Bit Lights | 1 × Astro Light Regular - White 30cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 30 cm lead reaches the chosen Dock. |
| 8 x Pink 30cm Bit Lights | 8 × Astro Light Regular - Pink 30cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 30 cm lead reaches the chosen Dock. |
| 3 x Green 30cm Bit Lights | 3 × Astro Light Regular - Green 30cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 30 cm lead reaches the chosen Dock. |
| 5 x Cool White 15cm Bit Lights | 5 × Astro Light Regular - Cool White 15cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 15 cm lead reaches the chosen Dock. |
| 5 x Cool White 30cm Bit Lights | 5 × Astro Light Regular - Cool White 30cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 30 cm lead reaches the chosen Dock. |
| 1 x Flashing White 30cm Bit Light | 1 × Astro Light Regular - Flashing White 30cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 30 cm lead reaches the chosen Dock. |
| 2 x Yellow 15cm Bit Lights | 2 × Astro Light Regular - Yellow 15cm ↗ | Keep one light at each original fixture. Route the flat lead without pinching it and confirm that its 15 cm lead reaches the chosen Dock. |
| 8 x 6-Port Expansion Board | 8 × Dock 6 ↗ | Astro ports are separate from the two Belt sockets. Mount the larger 2.0 housing with its included Tether; check the 1.0 board location has clearance. |
| 4 x 8-Port Expansion Board | 4 × Dock 9 ↗ | Astro ports are separate from the two Belt sockets. Mount the larger 2.0 housing with its included Tether; check the 1.0 board location has clearance. |
| 1 x 12-Port Expansion Board | 1 × Dock 9 ↗ 1 × Dock 3 ↗ | Astro ports are separate from the two Belt sockets. A 12-port board becomes Dock 9 + Dock 3, requiring two attachment locations and a linking Belt. |
| 1 x Flicker Effects Board | 1 × FX Spectrum ↗ | Use FX Spectrum with the closest appropriate mode: Elements for fire/flicker, Pulse, Gun, Emergency, Spooky, Sequence, Traffic or Glitter. Timing and output groups differ from 1.0. Each includes one 15 cm Belt and a 3×3 Tether. |
| 10 x 5cm Connecting Cables | 10 × Belt 5cm ↗ | Preserves the original nominal cable length. Belt plugs and routes differ; measure reach including bends before ordering. |
| 13 x 15cm Connecting Cables | 12 × Belt 15cm ↗ | Preserves the original nominal cable length. Belt plugs and routes differ; measure reach including bends before ordering. 1 of these 15 cm Belts are supplied with the FX Spectrum controllers and deducted from standalone purchases. |
| 3 x 30cm Connecting Cables | 3 × Belt 30cm ↗ | Preserves the original nominal cable length. Belt plugs and routes differ; measure reach including bends before ordering. |
| 1 x USB Power Cable | No separate purchase | Power changes to a 60 cm USB Flux Belt and separately purchased manufacturer-specified 5V/2.4A supply. Old battery/USB alternatives are not added twice. |
| 2.0 effect branch distribution | 1 × Split Dock ↗ | Each Split Dock has four Belt sockets: incoming power, effect-controller branch and onward trunk leave one spare. Keep steady lights off effect outputs. |
| Additional 2.0 links | 3 × Belt 50cm ↗ | 30 power-network components need at least 29 links. 25 source-length Belts plus 1 Belts included with FX controllers leave 3 additional links. 50 cm is a conservative routing allowance, not a measured installation length. |
| 2.0 USB power entry | 1 × Flux Belt 60cm ↗ | One Flux Belt per retained power group (old AA/USB alternatives combined). USB adapter or power bank excluded. Multiple sources must feed electrically separate networks; never join powered outputs. |
BRING YOUR OWN BRICKS
THE EXTRA
LEGO PIECES.
The lighting cart excludes the LEGO set and all extra LEGO pieces. These are the pieces listed in the original guide; adapting 2.0 mounting may require additional pieces.
- 8 × Plate 1x6 (Any Colour)
- 8 × Black 1×1 Modified Plate Rounded w Handle
- 15 × Black Round Plate 1x1 w Open Stud
- 3 × Black Arm Skeleton, Bent w Clips (Horizontal Grip)
- 5 × Black Tile 1x1 w Clip
- 2 × White Round Plate 1x1 w Open Stud
- 5 × Trans Clear 2x2 Plate w Rounded Bottom
- 1 × Black Plate 1×2 modified w Handle on End
- 1 × Black Plate 1×2 modified w stud jumper
- 1 × Black Plate 1x6
- 5 × Trans Clear Round Plate 1x1
- 1 × Trans Red Round Plate 1x1
Match shape, size and colour against the original guide. Element IDs are omitted where the source does not identify them. Docks and Meteors include the Tethers stated on their product listings.
PACK-AWARE PARTS
CHECK IT.
THEN BUILD YOUR CART.
Enter individual compatible 2.0 components you already own. A pack can contain multiple lights, strings or Belts. Included FX controller Belts are deducted automatically; if you own an FX controller, enter any separate Belts you own as well.
| 2.0 product | Need | Own | Per pack | Buy packs | Spare | AUD |
|---|---|---|---|---|---|---|
| Loading the parts list… | ||||||
Prices and stock checked 29 October 2026. Shipping, taxes, discounts and live availability are determined by the retailer. A Flux Belt is a power cable, not a USB power supply.
CHECK THE SOURCE
ORIGINAL
INSTRUCTIONS.
LIGHT MY BRICKS – Ninjago City Gardens 71741 Light Kit Instructions – Part 1 – Compressed ↗Original lighting inventory
- 14 x White Strip Lights
- 13 x Blue 30cm Bit Lights
- 10 x White 15cm Bit Lights
- 1 x White 30cm Bit Lights
- 8 x Pink 30cm Bit Lights
- 3 x Green 30cm Bit Lights
- 5 x Cool White 15cm Bit Lights
- 5 x Cool White 30cm Bit Lights
- 1 x Flashing White 30cm Bit Light
- 2 x Yellow 15cm Bit Lights
- 8 x 6-Port Expansion Board
- 4 x 8-Port Expansion Board
- 1 x 12-Port Expansion Board
- 1 x Flicker Effects Board
- 10 x 5cm Connecting Cables
- 13 x 15cm Connecting Cables
- 3 x 30cm Connecting Cables
- 1 x USB Power Cable
Original instructions and kit photography © Light My Bricks. Conversion commentary and calculations by BrickLight Chronicles. LEGO® and Light My Bricks are not endorsing this converter.